Components have to be discovered by any suitable technique other than that plates and billets For warm-drawn cylinders has to be marked with the warmth variety.
(d) No human being might mark or normally certify a packaging or container as meeting the requirements of the producing special allow Except if that particular person would be the holder of or a celebration to that Unique permit, an agent of the holder or party for the purpose of marking or certification, or even a third party tester.
(4) Identify porosity of filling and tare weights; confirm compliance of marking with prescribed specifications; attain important copies of steel shell stories prescribed in paragraph (b) of this section; and furnish complete exam stories required by this specification to the person who has finished the producer in the cylinders and, on ask for, to your purchaser.
This check might be made use of and need to be as demanded by CGA C-3. The specimen need to be bent right up until the elongation for the outer surface, adjacent to the foundation with the weld, among the lightly scribed gauge strains a to b, has to be at least twenty percent, besides this proportion could be lessened for steels using a tensile toughness in excessive of fifty,000 psig, as furnished in paragraph (k) of the segment.
(i) The phrase “spun” or “plug” should be positioned near the DOT specification marking when an conclusion closure while in the completed cylinder has been welded with the spinning process, or effected by plugging.
(2) If the porosity of each cylinder isn't identified, a cylinder taken at random from many two hundred or fewer must be tested for porosity. When the test cylinder fails, each cylinder within the great deal could possibly be tested individually and people cylinders that pass the test are satisfactory.
You happen to be employing a browser that won't supported by Fb, so we've redirected you to a simpler version to provde the best expertise.
(1) Each individual cylinder have to be uniformly and appropriately heat dealt with before check by the relevant strategy referenced in desk 1 of appendix A to this part. Heat procedure needs to be achieved In spite of everything forming and welding operations, apart from that when brazed joints are utilised, heat therapy need to stick to any forming and welding functions, but might be performed just before, all through or following the brazing functions (see paragraph (n) of the segment for weld repairs).
(2) Heat therapy is just not demanded after welding or brazing weldable low carbon components to attachments, laid out in paragraph (file)(1) of this area, of similar product that have been Beforehand welded or brazed to the top or base of cylinders and properly warmth handled, provided this kind of subsequent welding or brazing does not make a temperature in excess of four hundred °File in any Portion of the very best or base materials.
(one) Just about every cylinder needs to be heated and held at the appropriate temperature for a minimum of just one hour for every inch of thickness based on the most thickness website of your cylinder after which you can quenched in an appropriate liquid medium aquiring a cooling fee not in extra of 80 p.c of drinking water.
(ii) The examination needs to be on the weld concerning the parallel steel plates with a push by using a welded seam, at appropriate angles into the plates. Any projecting appurtenances may be Reduce off (by mechanical indicates only) before crushing.
Cylinders should be produced by greatest appliances and strategies. No defect is permitted that is likely to weaken the concluded cylinder appreciably. A fairly easy and uniform surface finish is required. The thickness from the spun base is, underneath no problem, for being lower than two times the minimal wall thickness of the cylindrical shell; these types of base thickness should be calculated in an area bounded by a line symbolizing the factors of Make contact with concerning the cylinder and flooring if the cylinder is in a vertical place.
Cylinders has to be produced working with equipment and processes suitable to make certain that each cylinder developed conforms to the necessities of the subpart. No fissure or other defect is permitted that is probably going to weaken the completed cylinder appreciably. A fairly smooth and uniform floor finish is needed. If not originally free of charge from such defects, the surface could possibly be machined or in any other case taken care of to reduce these defects.
(ii) The filling substance need to be uniform in excellent and free of voids, except that a properly drilled in to the filling content beneath the valve is approved In the event the effectively is full of a fabric of these kinds of variety the features from the filling material usually are not impaired;